稀土灼烧过程温湿度场仿真分析

影响稀土灼烧工艺的因素十分复杂,关系产品质量稳定及能耗,现行工艺存在优化空间。通过剖析灼烧窑中温度和湿度分布状况,运用κ-ε双方程湍流模型、流体传热、多孔介质传热等理论,按特定组分运输模式,建立灼烧过程质量、动量和能量耦合传递数学模型。设置不同边界导入Fluent环境对数学模型进行仿真试验,完成数据处理实现工艺参数优化。结果表明所建模型能准确反映灼烧窑中温湿度场分布及变化,且最终仿真结果与实际灼烧后的产品湿度含量相符合。     

Lean production system design for fishing net manufacturing using lean principles and simulation optimization

Value stream mapping (VSM) is a useful tool for describing the manufacturing state, especially for distinguishing between those activities that add value and those that do not. It can help in eliminating non-value activities and reducing the work in process (WIP) and thereby increase the service level. This research follows the guidelines for designing future state VSM. These guidelines consist of five factors which can be changed simply, without any investment. These five factors are (1) production unit; (2) pacemaker process; (3) number of batches; (4) production sequence; and (5) supermarket size. The five factors are applied to a fishing net manufacturing system. Using experimental design and a simulation optimizing tool, the five factors are optimized. The results show that the future state maps can increase service level and reduce WIP by at least 29.41% and 33.92% respectively. For the present study, the lean principles are innovatively adopted in solving a fishing net manufacturing system which is not a well-addressed problem in literature. In light of the promising empirical results, the proposed methodologies are also readily applicable to similar industries.     

Simultaneous process optimization and heat integration based on rigorous process simulations

This paper introduces a simultaneous process optimization and heat integration approach, which can be used directly with the rigorous models in process simulators. In this approach, the overall process is optimized utilizing external derivative-free optimizers, which interact directly with the process simulation. The heat integration subproblem is formulated as an LP model and solved simultaneously during optimization of the flowsheet to update the minimum utility and heat exchanger area targets. A piecewise linear approximation for the composite curve is applied to obtain more accurate heat integration results. This paper describes the application of this simultaneous approach for three cases: a recycle process, a separation process and a power plant with carbon capture. Case study results indicate that this simultaneous approach is relatively easy to implement and achieves higher profit and lower operating cost and, in the case of the power plant example, higher net efficiency than the sequential approach.     

Using a Discrete-Event System Specifications (DEVS) for designing a Modelica compiler

We introduce a new architecture for the design of a tool for modeling and simulation of continuous and hybrid systems. The environment includes a compiler based on Modelica, a modular and a causal standard specification language for physical systems modeling (the tool supports models composed using certain component classes defined in the Modelica Standard Library, and the instantiation, parameterization and connection of these MSL components are described using a subset of Modelica). Models are defined in Modelica and are translated into DEVS models. DEVS theory (originally defined for modeling and simulation of discrete event systems) was extended in order to permit defining these of models. The different steps in the compiling process are show, including how to model these dynamic systems under the discrete event abstraction, including examples of model simulation with their execution results.     

High-voltage and low specific on-resistance power UMOSFET using P and N type columns

For the first time, we present the unique features exhibited by power 4H–SiC UMOSFET in which N and P type columns (NPC) in the drift region are incorporated to improve the breakdown voltage, the specific on-resistance, and the total lateral cell pitch. The P-type column creates a potential barrier in the drift region of the proposed structure for increasing the breakdown voltage and the N-type column reduces the specific on-resistance. Also, the JFET effects reduce and so the total lateral cell pitch will decrease. In the NPC-UMOSFET, the electric field crowding reduces due to the created potential barrier by the NPC regions and causes more uniform electric field distribution in the structure. Using two dimensional simulations, the breakdown voltage and the specific on-resistance of the proposed structure are investigated for the columns parameters in comparison with a conventional UMOSFET (C-UMOSFET) and an accumulation layer UMOSFET (AL-UMOSFET) structures. For the NPC-UMOSFET with 10 µm drift region length the maximum breakdown voltage of 1274 V is obtained, while at the same drift region length, the maximum breakdown voltages of the C-UMOSFET and the AL-UMOSFET structures are 534 and 703 V, respectively. Moreover, the proposed structure exhibits a superior specific on-resistance (R_on,sp) of 2 mΩ cm², which shows that the on-resistance of the optimized NPC-UMOSFET are decreased by 56% and 58% in comparison with the C-UMOSFET and the AL-UMOSFET, respectively.     

航空发动机复杂扭曲叶片分步电解加工研究

为实现复杂扭曲叶片在较小间隙下的稳定加工,提出了一种分步式电解加工的工艺方法,建立了复杂扭曲叶片小间隙(0.2 mm)和大间隙下(0.5 mm)扭曲流道的流道模型,采用有限元法进行了流场仿真研究,结果表明增加流道间隙可以解决流道中涡流和流场紊乱的问题。开展了复杂扭曲叶片小间隙连续式加工和分步式加工的试验研究。结果表明,采用小间隙连续式加工,当阴极进给至3.8 mm位置时,在叶片排气边靠近叶根流道扭曲处出现短路打火情况;而采用分步式加工方式能够实现加工的顺利进行。     

Modelling,simulation and identification of an engine air path electromechanical actuator

This paper deals with the modelling and the identification of an electromechanical Diesel engine actuator. The studied Bosch GPA-S actuator is designed for swirl/tumble flaps to control the air amount entering into the cylinder. This study aims to design a complete simulator that reproduces, with sufficient accuracy, the actuator dynamics taking into account the effects of the friction phenomenon. Hence, an overview of the actuator structure and its operation principle is first given. Then, its mathematical model as well as the nonlinearity, related to its behaviour, is discussed. Next, three identification procedures, which allow estimating both the system parameters and the friction model coefficients, are introduced. Finally, simulation results, using MATLAB, and experimental results, using LabVIEW, are presented demonstrating the effectiveness of the proposed techniques.     

基于多体动力学仿真的冰箱助吸器优化设计

某款冰箱在关门过程中,门体在多个小角度处出现悬停的现象,影响用户的体验。针对这一问题,基于多体动力学仿真对冰箱助吸器进行了优化设计。将助吸器变形量、刚度、有效力臂接触位置点至铰链轴心连线长度,以及这一连线与接触位置法向夹角作为关键因子,研究关键因子与设计目标之间的关系,进行助吸器的结构设计与性能评估。在此基础上,基于多体动力学仿真,实现助吸器的优化,并形成最终设计方案。基于多体动力学仿真进行优化设计,可以缩短开发周期,提高设计效率,具有较高的实用价值。     

Service composition for generic service graphs

Service composition is a promising approach to multimedia service provisioning, due to its ability to dynamically produce new multimedia content, and to customize the content for individual client devices. Previous research work has addressed various aspects of service composition such as composibility, QoS-awareness, and load balancing. However, most of the work has focused on applications where data flow from a single source is processed by intermediate services and then delivered to a single destination. In this paper, we address the service composition problem for multimedia services that can be modeled as directed acyclic graphs (DAGs). We formally define the problem and prove its NP hardness. We also design a heuristic algorithm to solve the problem. Our simulation results show that the algorithm is effective at finding low-cost composition solutions, and can trade off computation overhead for better results. When compared with a hop-by-hop approach for service composition, our algorithm can find composition solutions that aress 10% smaller in cost, even when the hop-by-hop approach uses exhaustive searches.